9*7 MM Microphone Electret Microphone with 2 Pin – KSH 70 at HIMASTORES Mombasa – best electronics in Kenya

9*7 MM Microphone Electret Microphone with 2 Pin

SKU: HMJ677 Category: Sensors
KSH 70.00
Out of Stock

Product Description

9x7mm Electret Microphone with 2 Pin

Compact Electret Condenser Microphone Cartridge

The 9x7mm Electret Microphone is a compact, highsensitivity condenser microphone cartridge featuring a builtin FET amplifier and 2pin interface. This smallform-factor microphone delivers clear audio capture for voice, sound, and acoustic detection applications with Arduino, ESP32, and other microcontroller projects.

Builtin FET preamplifier for high sensitivity audio capture
Requires 2-10V DC power through load resistor (2.2kΩ typical)
Polarity matters - connect positive pin to power, negative to ground

Technical Specifications

ParameterValue
Dimensions9mm x 7mm
TypeElectret Condenser
Polar PatternOmnidirectional
Sensitivity-42dB ±3dB
Frequency Range50Hz - 20kHz
Impedance≤2.2kΩ
S/N Ratio≥58dB
Supply Voltage2V - 10V DC
Current Consumption≤0.5mA
Operation Temp-20°C ~ 70°C
Pin Configuration2 pins (Positive + Negative)
PolarityPositive pin marked (red or "+")

= Key Features =

High Sensitivity - Clear audio capture for voice and sound

Builtin FET Integrated amplifier for strong output signal

Omnidirectional - Captures sound from all directions

Small Footprint - 9x7mm size for compact projects

Wide Voltage Range 210V DC operation for flexibility

Low Power - ≤0.5mA current consumption

Simple Interface 2pin connection for easy integration

= Applications =

  • Voice recording and audio capture
  • Sound detection and monitoring
  • Clap-activated circuits and projects
  • Audio visualizers and reactive lighting
  • Voice command and recognition
  • Security and surveillance systems
  • Wearable electronics
  • Phone and communication devices

Wiring Guide

Microphone PinConnectionDescription
Positive (+)3.3V or 5V (through 2.2kΩ resistor)Power supply with bias resistor
Negative (-)GNDCommon ground
Signal OutputAnalog Pin (A0)Connect at resistor junction point

> Typical circuit: Connect VCC→2.2kΩ resistor→Microphone Positive→Output to ADC

Output signal is AC waveform centered at ~VCC/2
Reverse polarity will damage the microphone

Typical Connection Circuit

VCC (5V) ── 2.2kΩ Resistor ──┬── Microphone (+) ── Output to Analog Pin

Microphone (-) ─── GND

Use 2.2kΩ bias resistor for 5V operation
For 3.3V use 1kΩ or 2.2kΩ resistor
Add 10µF capacitor in series for AC-only audio output

Arduino Test Code

int micPin = A0;

int micValue = 0;

void setup() {

Serial.begin(9600);

}

void loop() {

micValue = analogRead(micPin);

Serial.println(micValue);

delay(10);

}


Why Choose This Microphone?

High sensitivity and clear audio capture
Built-in amplifier for strong output
Compact size fits any project
Low power consumption
Easy to integrate with Arduino
Cost-effective audio solution

√ Works with 3.3V and 5V systems

√ Simple 2-pin connection

√ No additional amplifier required for basic use

√ Reliable and durable construction

√ Perfect for DIY sound projects


Safety Precautions

Connect with correct polarity - reverse polarity will damage
Do not exceed 10V supply voltage
Keep away from moisture and physical damage
Protect from electrostatic discharge (ESD)
Handle with care - sensitive membrane
For longer connections, use shielded wire to reduce noise
For clean audio, position mic away from vibration sources

What's Included

  1. 9x7mm Electret Microphone Cartridge

The 9x7mm Electret Microphone delivers highquality audio capture in a compact, easyto-use package. Perfect for voice, sound detection, and creative Arduino projects.

ELECTRETMIC MICROPHONE AUDIOSENSOR SOUNDDETECTION 9X7MM ARDUINO ESP32 DIY VOICERECORDING SOUNDSENSOR #COMPACT New Best Seller Electret Mic